Williamson TMP-105 Especificações

Printed on 100% recycled paper 670-000-004/1010 Temp-O-Matic Oil Furnace TMP Multi-Position (Counterflow / Horizontal) Furnace Manual Content

TMP Oil Furnaces – Furnace Manual 10 670-000-004/1010 3 Connect supply and return ducts (continued) Duct sizing (continued) Table 5 Typical du

TMP Oil Furnaces – Furnace Manual 670-000-004/1010 11 4 Venting General venting requirements Failure to follow all instructions can result in

TMP Oil Furnaces – Furnace Manual 12 670-000-004/1010 5 Connect fuel oil piping General oil piping requirements • Location and installation of o

TMP Oil Furnaces – Furnace Manual 670-000-004/1010 13 Notes:

TMP Oil Furnaces – Furnace Manual 14 670-000-004/1010 6 Wire furnace & burner Electric shock hazard. It can cause severe personal injury or de

TMP Oil Furnaces – Furnace Manual 670-000-004/1010 15 6 Wire furnace & burner (continued) PLB Oil Furnaces – Furnace Manual Figure

TMP Oil Furnaces – Furnace Manual 16 670-000-004/1010 6 Wire furnace & burner (continued) PLB Oil Furnaces – Furnace Manual Figure

TMP Oil Furnaces – Furnace Manual 670-000-004/1010 17 Gasket for overfire pressure reading 7 Start up Follow information below to prevent seve

TMP Oil Furnaces – Furnace Manual 18 670-000-004/1010 8 Checkout procedure Furnace selection  ..1. Heat loss ... BTU

TMP Oil Furnaces – Furnace Manual 670-000-004/1010 19 9 Troubleshooting Check

2 670-000-004/1010 READ THIS FIRST! Failure to adhere to the guidelines below can result in severe personal injury, death or substan

TMP Oil Furnaces – Furnace Manual 20 670-000-004/1010 10 Service and maintenance Follow the “Service and maintenance” procedures given throughout

TMP Oil Furnaces – Furnace Manual 670-000-004/1010 21 Handling ceramic fiber and fiberglass materials HANDLING OR REMOVAL OR COMBUSTION CHAMBER

TMP Oil Furnaces – Furnace Manual 22 670-000-004/1010 10 Service and maintenance (continued) To lubricate and inspect blower motor DO NOT lubricat

TMP Oil Furnaces – Furnace Manual 670-000-004/1010 23 11 Components and replacement parts Figure 7 Model TMP furnaces – Component locations B

TMP Oil Furnaces – Furnace Manual 24 670-000-004/1010 B50098 Rev.B ITEM DESCRIPTION PART #1Complete heat exchanger (item 2, 3, 4, 5 & 6 include

TMP Oil Furnaces – Furnace Manual 670-000-004/1010 25 12 Dimensions and ratings Figure 5 Model TMP dimensional data – ALL DIMENSIONS IN INCHE

TMP Oil Furnaces – Furnace Manual 26 670-000-004/1010 12 Dimensions and ratings Model TMP-105, Burners data Air

TMP Oil Furnaces – Furnace Manual 670-000-004/1010 27 13 Owner’s information The furnace must be inspected and started ANNUALLY, at the beginn

TMP Oil Furnaces – Furnace Manual X40105 Rev. K

TMP Oil Furnaces – Furnace Manual 670-000-004/1010 3 1 Check furnace location Pre-installation checklist Verify code compliance  Local, state

TMP Oil Furnaces – Furnace Manual 4 670-000-004/1010 1 Check furnace location (continued) Air for combustion and ventilation Adequate combustio

TMP Oil Furnaces – Furnace Manual 670-000-004/1010 5 1 Check furnace location (continued) Air contamination Please review the following informa

TMP Oil Furnaces – Furnace Manual 6 670-000-004/1010 2 Prepare furnace and place in position Inspect & prepare furnace Remove furnace from c

TMP Oil Furnaces – Furnace Manual 670-000-004/1010 7 2 Prepare furnace and place in position (continued) Blocked Vent Shut-Off (BVSO) for chim

TMP Oil Furnaces – Furnace Manual 8 670-000-004/1010 3 Connect supply and return ducts Duct sizing Determine airflow CFM The temperature rise th

TMP Oil Furnaces – Furnace Manual 670-000-004/1010 9 3 Connect supply and return ducts (continued) Duct sizing (continued) Table 4 Typical d